1
00:00:00,000 --> 00:00:05,290
220千伏有载调压开关是一种可在空载和带负荷条件下

2
00:00:05,290 --> 00:00:08,826
无需停电即可调整变压器输出电压的装置

3
00:00:08,826 --> 00:00:12,496
通过分接头档位转换调节高压绕组匝数

4
00:00:12,496 --> 00:00:14,166
从而改变负荷侧电压

5
00:00:14,720 --> 00:00:17,250
由于越靠近中性点电压越低

6
00:00:17,250 --> 00:00:20,300
该调压开关通过改变中性点匝数

7
00:00:20,300 --> 00:00:22,013
以及通过范围开关

8
00:00:22,013 --> 00:00:23,613
选择线圈方向

9
00:00:23,613 --> 00:00:25,153
加位或者减位

10
00:00:25,153 --> 00:00:26,813
来转换电流方向

11
00:00:26,813 --> 00:00:29,013
选择增大或者抵消磁场

12
00:00:29,013 --> 00:00:31,346
使调节倍数增加一倍

13
00:00:31,347 --> 00:00:34,027
它分为操作系统和执行系统

14
00:00:34,027 --> 00:00:37,587
操作系统通过电机或手动转动提供动力

15
00:00:37,587 --> 00:00:40,307
执行机构用于切换绕组匝数

16
00:00:40,307 --> 00:00:44,040
其中执行机构由选择开关和切换开关组成

17
00:00:44,040 --> 00:00:47,790
选择开关连接各个调节的不同匝数的绕组

18
00:00:47,790 --> 00:00:49,500
分别为1-8号抽头

19
00:00:50,067 --> 00:00:53,427
在三相系统中 每相又分为两层

20
00:00:57,652 --> 00:01:01,977
上层为奇数1357号抽头及范围开关共用抽头

21
00:01:01,977 --> 00:01:06,173
下层为偶数2468号抽头及范围开关共用抽头

22
00:01:06,173 --> 00:01:09,473
用于选择需调节的绕组和绕组的方向

23
00:01:09,473 --> 00:01:12,023
也用于预选需要转换的匝数

24
00:01:12,023 --> 00:01:14,133
切换开关主要是选择的匝数

25
00:01:14,694 --> 00:01:16,867
每相绕组有4个触头

26
00:01:16,867 --> 00:01:20,934
分别为A1到A4

27
00:01:20,934 --> 00:01:24,374
B1到B4

28
00:01:24,374 --> 00:01:25,894
C1到C4

29
00:01:25,894 --> 00:01:28,587
总计12个触头

30
00:01:28,587 --> 00:01:35,467
通过步进方式 让一组或两组触头接通

31
00:01:35,468 --> 00:01:37,254
中间经过渡电阻

32
00:01:37,254 --> 00:01:45,641
顺利切换到预选匝数 后经中性点线排回到变压器中性点

33
00:01:45,642 --> 00:01:48,962
接下来让我们演示一下它的操作方法

34
00:01:48,962 --> 00:01:50,792
假设我们现在为一档

35
00:01:50,792 --> 00:01:52,502
想降低负载电压

36
00:01:52,502 --> 00:01:53,772
调节到二档

37
00:01:53,772 --> 00:01:55,642
由于遵循抵挡绕组少

38
00:01:55,642 --> 00:01:57,122
高档绕组多

39
00:01:57,122 --> 00:02:00,092
那么此时范围开关是在加档位置

40
00:02:00,092 --> 00:02:03,222
而选择开关绕组在 上层1号抽头位置

41
00:02:03,776 --> 00:02:09,322
我们手动摇动转动或者电机转动 经竖轴运动 横轴运动

42
00:02:09,323 --> 00:02:12,623
带动调压开关的选择开关的主轴运动

43
00:02:12,623 --> 00:02:14,023
经旋转齿盘

44
00:02:14,023 --> 00:02:16,803
拨动下端选择开关齿盘主轴运动

45
00:02:16,803 --> 00:02:20,029
让预选连接上层2号抽头绕组

46
00:02:20,030 --> 00:02:23,430
同时上端主轴带动切换开关快慢机

47
00:02:23,430 --> 00:02:26,900
使得触头中间的尾推弹簧机构有节奏的运动

48
00:02:27,457 --> 00:02:32,297
现在面临的情况是电经过下方分接开关1号绕组连接

49
00:02:32,297 --> 00:02:35,537
切换开关中的A1触头到达中性点

50
00:02:35,537 --> 00:02:41,883
分接开关2号绕组连接

51
00:02:41,884 --> 00:02:44,324
切换开关中的A4触头上

52
00:02:44,324 --> 00:02:47,844
首先连接A2

53
00:02:47,844 --> 00:02:53,790
然后断开A1触头

54
00:02:53,791 --> 00:02:55,377
接通A3触头

55
00:02:55,377 --> 00:02:58,924
断开A2触头

56
00:02:58,924 --> 00:03:02,684
连接第A4触头

57
00:03:02,684 --> 00:03:08,324
断开A3触头

58
00:03:08,325 --> 00:03:11,231
此时电经过分接开关2号绕组

59
00:03:11,231 --> 00:03:18,858
经过切换开关中的A4触头到达中性点

60
00:03:18,859 --> 00:03:21,659
这就是变压器经有载调压开关

61
00:03:21,659 --> 00:03:24,019
顺利从一档调节到二档的位置

62
00:03:24,579 --> 00:03:25,949
需要注意的是

63
00:03:25,949 --> 00:03:28,899
有载调压开关是不能跳档调节的

64
00:03:28,899 --> 00:03:30,659
只逐步一档一档调节

65
00:03:30,659 --> 00:03:33,885
当八档到九档时情况会比较特殊

66
00:03:33,886 --> 00:03:37,296
9档分为9A、9B和9C共三档

67
00:03:37,296 --> 00:03:39,816
9B为极性转换的标准档位

68
00:03:39,816 --> 00:03:40,992
可长期运转

69
00:03:40,992 --> 00:03:46,086
9A、9C为过渡档位 只可临时运行不可长期运行

70
00:03:46,086 --> 00:03:48,266
这就顺利的从加档位置

71
00:03:48,266 --> 00:03:50,076
切换到了减档位置

72
00:03:50,076 --> 00:03:52,619
从十档开始直至加到十七档

73
00:03:52,619 --> 00:03:56,059
其过程是1号绕组到8号绕组的切换

74
00:03:56,059 --> 00:03:58,759
从而完成1-17档的加档过程

75
00:03:58,766 --> 00:04:01,099
以实现负载的降压过程

76
00:04:01,100 --> 00:04:03,080
而减档则恰恰相反

77
00:04:03,080 --> 00:04:05,280
通过手动或电机反转

78
00:04:05,280 --> 00:04:08,340
下面为17档切换至1档的运动状态

79
00:04:08,340 --> 00:04:13,580
从而完成17-1档的减档过程 以实现负载的电压升高

80
00:04:13,580 --> 00:04:18,326
以上就是220千伏有载调压开关的构造和工作原理